2025 Updated Verified D-NWG-DS-00 dumps Q&As - Pass Guarantee or Full Refund
D-NWG-DS-00 PDF Questions and Testing Engine With 123 Questions
NEW QUESTION # 27
In which phase of networking design is the EPS tool most useful?
Response:
- A. During the planning phase to estimate environmental and power requirements
- B. During the scoping phase when identifying business needs
- C. During the testing phase to verify performance metrics
- D. During the deployment phase when devices are being installed
Answer: A
NEW QUESTION # 28
What is the purpose of deployment support in troubleshooting network issues during installation?
Response:
- A. To identify and resolve connectivity and configuration problems
- B. To analyze network traffic patterns
- C. To configure access control lists
- D. To provide ongoing network monitoring
Answer: A
NEW QUESTION # 29
Which of the following is NOT a primary function of the FastScript tool?
Response:
- A. Generating VLAN assignment scripts
- B. Automating device configuration
- C. Automating routing configuration
- D. Monitoring network traffic
Answer: D
NEW QUESTION # 30
What key aspect of the scoping phase helps ensure that the network design meets financial and technical requirements?
Response:
- A. Cost estimation using Financial Force
- B. Hardware configuration
- C. Network monitoring tools
- D. Cable management
Answer: A
NEW QUESTION # 31
Which item can be viewed directly from the Enterprise Project Services project dashboard?
Response:
- A. License Entitlement
- B. Installation Address
- C. Switch Configurations
- D. Design Details
Answer: B
NEW QUESTION # 32
What routing protocol is recommended when designing the leaf-spine network of a customer?
Response:
- A. Static
- B. BGP
- C. IS-IS
- D. PTP
Answer: B
NEW QUESTION # 33
Which is a limitation of FastList?
Response:
- A. It cannot be used with extensive lists.
- B. Is not compatible with Microsoft Edge.
- C. Delay in loading is evident on substantial lists.
Answer: C
NEW QUESTION # 34
Which tool is typically used during the scoping phase to identify and prioritize networking project requirements?
Response:
- A. Unisphere
- B. PowerSwitch
- C. FastList
- D. Control Station
Answer: C
NEW QUESTION # 35
A network engineer is designing a leaf-spine architecture based on Dell PowerSwitches. Which three best practices should be considered in this scenario when implementing BGP?
Response:
- A. Use the same ASN for each spine.
- B. Use iBGP between the leaf and spine.
- C. Use eBGP between the leaf and spine.
- D. Use one different ASN for each spine.
- E. Use one ASN per each leaf pair.
Answer: C,D,E
NEW QUESTION # 36
What is the primary purpose of using templates in a network design project?
Response:
- A. To generate real-time network traffic reports
- B. To automate network configuration
- C. To assign IP addresses dynamically
- D. To standardize documentation and ensure consistency
Answer: D
NEW QUESTION # 37
What are three of the phases of an Enterprise Project Services project?
Response:
- A. Scoping
- B. Close
- C. Approval
- D. Design
Answer: A,D
NEW QUESTION # 38
Which of the following are key considerations during Layer 3 (L3) network planning?
Response:
- A. Network topology
- B. Routing protocols
- C. IP address allocation
- D. VLAN segmentation
Answer: A,B,C
NEW QUESTION # 39
Which tasks are performed during the scoping phase to align the network design with business requirements?
Response:
- A. Installing routers and switches
- B. Identifying project requirements and constraints
- C. Scheduling network monitoring solutions
- D. Implementing network security policies
Answer: B
NEW QUESTION # 40
Which tool is most commonly used for Layer 2 (L2) network planning?
Response:
- A. Unisphere
- B. FastList
- C. EPS Tool
- D. OS10 Licensing
Answer: D
NEW QUESTION # 41
What is the purpose of verifying the EDP pre-deployment checklist before a network deployment?
Response:
- A. To ensure that all devices have the latest firmware
- B. To assign IP addresses to network devices
- C. To confirm the deployment is aligned with enterprise standards and policies
- D. To configure security policies
Answer: C
NEW QUESTION # 42
A customer needs help gathering detailed analytics on their PowerSwitch. The Secure Remote Services Gateway has been set up and configured to act as an aggregator for the data that is obtained. Which component should be deployed?
Response:
- A. SONiC
- B. SFS
- C. Squeeze utility
- D. CloudIQ collector
Answer: D
NEW QUESTION # 43
Match the following roles in networking design with their corresponding responsibilities:
Role
Network Architect
Network Administrator
Security Engineer
Systems Engineer
Responsibility
A) Designs the entire network structure
B) Manages day-to-day network operations
C) Implements firewalls and intrusion detection
D) Manages servers and network services
Response:
- A. Network Architect - A
- B. Network Architect - D
- C. Network Architect - A
- D. Network Architect - C
Answer: A
NEW QUESTION # 44
Which of the following is a common task performed by deployment support during a network installation?
Response:
- A. Monitoring traffic patterns
- B. Performing vulnerability assessments
- C. Troubleshooting hardware and software issues
- D. Designing IP addressing schemes
Answer: C
NEW QUESTION # 45
What is the primary function of the Troubleshooting Template in network documentation?
Response:
- A. It manages software licensing for network devices
- B. It provides a detailed list of all VLANs and their configurations
- C. It records and tracks network issues and their resolutions
- D. It verifies network configurations after deployment
Answer: C
NEW QUESTION # 46
Which of the following are responsibilities of a network design professional?
Response:
- A. Writing software code
- B. Providing disaster recovery options
- C. Identifying business requirements
- D. Developing a security architecture
Answer: B,C,D
NEW QUESTION # 47
Which of the following should be considered during the planning phase of a Cyber Recovery Vault?
Response:
- A. Physical distance between production and recovery sites
- B. Network switch redundancy
- C. The use of thin provisioning
- D. VLAN segmentation
Answer: A
NEW QUESTION # 48
In which scenario would the FastList tool be most beneficial during the scoping phase of a network design project?
Response:
- A. When you need to estimate the cost of network hardware
- B. When you need to prioritize and organize project requirements for a new data center design
- C. When you need to generate deployment scripts for network devices
- D. When you need to calculate the environmental requirements of a network rack
Answer: B
NEW QUESTION # 49
What is the primary role of scripting tools like FastScript in network design projects?
Response:
- A. To document network changes
- B. To track network performance metrics
- C. To automate network device configuration and reduce manual errors
- D. To perform network vulnerability assessments
Answer: C
NEW QUESTION # 50
......
Exam Engine for D-NWG-DS-00 Exam Free Demo & 365 Day Updates: https://testoutce.pass4leader.com/EMC/D-NWG-DS-00-exam.html